• Gearbox
• Engine
• Engine
• Liquids
• Gearbox

Priora engine oil recommended by the manufacturer. How much engine oil is needed for a Lada Priora How much oil to fill in a Priora 16 engine

The manufacturer recommends replacing the filter and engine oil every 15 thousand kilometers. When operating the Lada Priora in urban conditions, the lubricant is changed every 7-10 thousand. Replacement is usually done independently.

You can find out how much oil to pour into the Priora engine by visiting the manufacturer’s website or reading the instruction manual. In addition, the type of recommended oil is also indicated there. This article will be a good help for a novice car enthusiast. It will answer questions related to oil replacement and consumption.

[Hide]

Consumption

The average volume of lubricant that must be filled during replacement is from 3.2 to 3.4 liters; this value can be determined experimentally. First, fill in 3.2 liters of new oil.

Then, after the engine has been running for about five minutes, you should measure the fluid level using a dipstick. The norm is considered when the mark is located between the minimum and maximum levels. If necessary, add oil. It is important not to pour above the maximum level. You should buy 4 liters of fuel and lubricants, so that after replacement you have something to add if necessary.

When operating a Lada under normal conditions without loads, consumption of up to one liter per 1000 kilometers is considered normal. How much the actual consumption will be depends on the operating conditions. Consumption will be higher when traveling at high speeds and when accelerating frequently. In a new engine, the first time during operation the piston rings, cylinder walls and pistons are ground in, so oil consumption is higher.

If oil consumption is significant, the cause may be wear of the valve seals. If necessary, they must be replaced. By the type of exhaust gases, you can determine whether the lubricant burns along with the fuel. You can judge the condition of the valve seals by the carbon deposits on the spark plugs: if it is black, then the oil seals need to be changed. In addition, you should check the compression in the cylinders, which also affects fuel consumption. If the level is low, repairs will be necessary, which consists of replacing rings, valve stem seals and grinding in valve seats.

Replacement process

Every driver must constantly monitor the oil level and change it regularly, as it affects the quality of engine operation, lubricates parts, reducing the load. The replacement process begins with the purchase of high-quality oil suitable for Lada Priora.

What kind of oil to fill

Purpose of the oil:

• lubricant;
• corrosion protection;
• cooling of metal parts;
• removal of wear particles and unburnt gasoline residues.

Lubricating fluids can be mineral, obtained from the distillation of oil, and synthetic - chemical synthesis. Mineral ones lose their working qualities faster, leave residues on the engine, and oxidize more strongly. If there is a long gap between servicing, it is better to use synthetics. You should not mix two types, only as a last resort if it is not possible to find an identical one on the route.

Frets depend on the specific model. Synthetics are good for Priora; if you have financial difficulties, you can take semi-synthetics. The main characteristic of the oil is the viscosity index - SAE. For example, the name says 0W-40 - this is the viscosity index for winter operation of the car; the engine oil will be in a liquid state even at temperatures of -30-35 degrees.

The number before the letter W determines the lower limit of operation (the lower the value, the lower the operating temperature can be), the second digit determines the upper limit. In our example, the upper operating temperature can be +35- +40 degrees.

Synthetic motor oil

According to API recommendations, the choice of fuels and lubricants is influenced by the year of manufacture of the engine. Since 2003, the 128 engine has been produced for the Lada Priora; from 2007 - 127, from 2011 - 21116, from 2013 - 126. For example, for a 128 engine, oil marked SL/SM is more suitable, for the rest - with the mark SM (used on engines that released after 2004).

You can find out which oil is best to use from the recommendations for operating a Lada Priora car. They provide a list of recommended fuels and lubricants from which you should make a choice.

Tools

When replacing fuel and lubricants, the oil filter should also be changed so that dirt does not get into the new fluid. To carry out the work, you must prepare the following tools and materials:

• a container with a volume of approximately 5 liters into which the used lubricant will be drained (it cannot be drained onto the ground);
• a rag, rags to remove drips;
• a brush with metal teeth;
• new oil filter;
• key for 10 and 17;
• special key for removing the filter;
• engine oil.

Having prepared everything you need, you can start replacing.

Replacement steps

Changing the oil consists of the following steps:

1. It is better to change fuel and lubricants after a trip, when it is warmed up. Otherwise, the engine must be warmed up to operating temperature. To do this, you need to start the engine and let it idle for 10 minutes.
2. We put the Priora on a lift. You can put it on the handbrake, put stops under the rear left wheel, install a jack on the front right and remove the wheel.
3. Having opened the hood, unscrew the cap from the filler neck.
4. We free the motor from the mudguard. Using a 10mm wrench, unscrew the fastening nuts and remove the mudguard.
5. We clean the plug on the drain hole with a metal brush and a rag.
6. We place a container for waste liquid under the drain hole on the pallet.
7. Using a 17 wrench, unscrew the plug so as not to tear off the edges, it is better to use a socket head. You should drain the waste liquid very carefully, as it is hot.
8. The liquid flows out within 10-15 minutes. At this time, you can change the oil filter. It is located to the right of the exhaust manifold at the rear of the engine.
9. To replace the oil filter in the Lada Priora, there is a special wrench; it is better to use it. If there is no key, then you can use the “old-fashioned method”: pierce the oil filter with a screwdriver or an awl, and then, using them as a lever, move the thread from its place and unscrew the filter by hand. You must remove it carefully, as there may be residual lubricant in it.
10. Fill the new filter 2/3 full with oil so that after starting the engine, the valve drive parts do not experience oil starvation. It should be poured in several passes.
11. Lubricate the rubber o-ring on the filter with fuel and lubricants.
12. Screw the new filter onto the engine until the cylinder block flange touches the ring. It must be installed without distortion.
13. We return the drain plug to its place and remove the container with the waste liquid.
14. We pour new oil into the Lada Priora engine. It is necessary to pour carefully. You can cut a plastic bottle for this to use as a funnel.
15. It is recommended to pour three liters of liquid.
16. Let the fuel drain and check the oil level using a dipstick. To do this, first pull out the dipstick, wipe it with a rag and return it to its place. Then we take it out again and look at the fluid level. It should be between the maximum and minimum risks. It is important not to fill more than the maximum, this may affect the proper operation of the catalyst and mass air flow sensor.
17. Screw the cap onto the filler hole.
18. We start the engine idling and let it run for a few minutes to check for leaks from under the filter and drain cover. If the cover leaks, the lubricant consumption will increase. Therefore, if there are drips, you should tighten the lid better.
19. After turning off the engine, check the level again and add fluid if necessary.
20. Screw the mudguard back on.

During operation of the Priora, oil consumption and level should be regularly monitored. Using a dipstick, determine how much fuel is missing to the required level and add if necessary. To do this, you should carry a canister with the remaining oil after the change in the trunk.

Video “Changing the oil in the Lada Priora engine”

How much oil to fill into the Priora engine can be found in the book on the operation and repair of the vehicle. The oil and filter should be replaced every 15 thousand km of the vehicle. If Priora is operated exclusively in urban conditions, then repair work is carried out every 10 thousand km. During the operation of the car, the owner must know how much oil the engine consumes.

Rules for choosing a liquid

The average volume of lubricant that must be filled in during the replacement process is from 3.2 to 3.4 liters. If the car eats more oil than before, then you will need to check the tightness of the power unit. Lubricant leakage occurs when the gaskets wear out.

It is better to purchase lubricating fluid in quantities of 4 liters. When operating a car under normal conditions (without increased loads), the optimal consumption is 1 liter of lubricant per 1000 km. How much a car actually eats depends on weather, road and speed conditions.

Oil consumption increases when driving at high speeds and during numerous accelerations.

If the car is new, then the first time the engine grinds in the piston rings, pistons and cylinder walls. This increases oil consumption.

If the Priora consumes oil in large quantities, the reason may lie in the wear of the valve seals. If necessary, they need to be changed. If the soot color is black, then the caps are replaced with new ones. Auto mechanics recommend checking compression in the cylinders, as it has a direct impact on oil consumption. If the compression indicator is below normal, then the rings are replaced.

Types and purposes of lubricants

According to its intended purpose, the oil performs the following functions:

• provides lubrication and anti-corrosion protection;
• cools metal parts;
• Removes wear particles and unburnt gasoline residues.

Experts distinguish the following types of lubricants:

• mineral (obtained during the distillation of oil);
• synthetic (produced through chemical synthesis);
• semi-synthetic.

Each substance has certain properties and a different chemical composition. You can fill the Lada Priora with semi-synthetic fluid. To understand what a blended oil is, you need to study its composition. The first part is the basis of the lubricant, and the second is presented in the form of additives that have a direct impact on the quality of the engine oil. Motor oil manufacturers do not recommend mixing oils with different bases.

0W-40 fluid is ideal for operating a car in winter. Such motor oil will retain its original condition at a temperature of -35ºС.

The number 0 indicates the value of the lower operating limit. The second digit determines the upper limit. In the example considered, the value of the upper operating temperature can be +40ºС.

Oil change instructions

When replacing old oil, the oil filter must be replaced. This is done to prevent dirt from getting into the new liquid. To perform this work, use the following tools:

• plastic container with a volume of at least 4 liters;
• rags;
• brush with metal teeth;
• oil filter to replace;
• keys for 10 and 17;
• a special key designed to remove the filter;
• new motor oil.

Changing the oil in a Priora engine includes the following steps:

1. Repair work is carried out when the engine is warm.
2. The car is placed on a lift. You can use the option with a hand brake. A stop is placed under the rear left wheel, and a jack is installed under the front right wheel. The wheel is removed.
3. The hood opens, the cap is unscrewed from the neck of the tank.
4. The engine is freed from the mudguard. To do this, use a key of 10.
5. Then the cork is cleaned using a wire brush and an old rag.
6. Prepared containers are substituted for processing. The container is installed directly under the drain hole of the pan.
7. Using a 17 key, unscrew the plug. To avoid thread damage and edge breakage, it is recommended to use a socket head. Draining the waste should be done carefully, as it is hot.
8. The old oil flows out within 10-15 minutes. During this period of time, you can replace the old oil filter. To do this, use a special key or a homemade device (break through the old filter using an awl or screwdriver). The resulting structure is used as a lever. The new filter should be installed without distortion.

First you need to fill in 3.2 liters of new fluid. Then the engine starts. The car idles for 5 minutes. Then the engine turns off. The oil level is measured using a dipstick. The indicator is normal if the mark is located between the MAX and MIN icons. If necessary, add liquid. It is important not to overfill the oil above the maximum mark.

The filler cap is screwed on. The engine starts idling. The machine should operate in this mode for several minutes. If there are leaks under the lid, it must be tightened tighter. The engine is turned off. The oil level is rechecked. The above work is carried out independently or with the help of professionals.

Experts advise filling Priora gasoline engines with oil that corresponds to the SL or SJ group according to the API classification. The lubricant viscosity according to SAE is selected taking into account the climatic conditions in which Priora is operated. In summer it is recommended to use 5W40 oil, and in winter – 0W30. Normally, it is necessary to use the viscous substance recommended by the manufacturer for this model. In this case, oil consumption will decrease.

It is recommended to purchase oil from an official representative or from the manufacturer. To reduce fuel consumption by increasing the performance of the power unit to the maximum, products from Mobil, Castrol and Teboil are used. These products contain economical fuel additives that increase the service life of the internal combustion engine. If, when replacing the substance, the engine consumes more oil, then you will need to undergo diagnostics.

Experts recommend that when choosing a lubricant for the Lada Priora engine, take into account the year of manufacture of the vehicle - the older the car, the higher the viscosity of the engine oil should be. The model under consideration can be filled with synthetic and semi-synthetic viscous substances. These compounds work well in winter, as they do not freeze at sub-zero temperatures, improving the performance of the power unit.

Changing the oil in the Priora engine: how much oil and what kind to pour?

The Priora operating manual states that every 15 thousand kilometers you need to flood new oil. Experts advise replacing every 10,000 km, especially if the Priora is constantly used in urban areas. Replacement is a fairly common process, so even a novice motorist can do it. The material also carefully describes How many it is necessary to pour oil and what working fluid is best to choose.

Along with the oil, you will also need to change its filter - this is an absolute must, because working fluid remains inside the consumable. It should not mix with the new lubricant.

How many need to pour oil and which one to choose?

To find out how much is needed pour oil, again we turn to the Priora control - from 3.2.4 to 3.4 liters should be poured into the system. At first, 3.3.2 liters are poured. new oil. After a while, the power plant should run for about 5 minutes. Next you need to find out the level using a dipstick. If the mark is between the MIN and MAX values, it means the level has been met. If necessary, there is an option to add working fluid. The main thing is that the oil does not exceed the MAX level. You need to purchase 4 liters of oil.

Similar news

Replacement is carried out with the same brand that is filled in the system. We know the basic information about the engine - it is a 16-valve petrol unit. Samples with the following parameters are suitable for the Priora power plant:

How much oil to fill in the VAZ 2112 engine.

Lada Priora - oil change

change oils by Lada car Priora without using a trestle, just a jack and keys.

• 5W-30, operating temperatures: from 30 to 25°C.
• 5W-40 – from 30 to 40°С.
• 10W-40 – from 25 to 40°С.
• 15W-40 – from 15 to 40°С.

If you live in a cold region, you can choose 0W. This type of lubricant does not freeze at 35°C. There are also options for summer use. Of course, they will freeze even in slight frost. The Priora passport indicates which oil is best to pour and how much is required.

Replacement

What will you need?

Now we know how much oil to pour, all that remains is to replace it in the engine. You will need:

• The key is "17".
• Filter removal tool.
• New oil.
• Oil filter.
• Container for draining old fluid.
• Clean rags.

Replacing the lubricating fluid in 16 and 8 valve engines is carried out in the same way on an inspection pit or on a lift. It is recommended to wear thick gloves and a long-sleeved robe.

Similar news

Changing the fluid in the engine should be carried out immediately after the trip, while the Priora’s power plant has not cooled down. If the engine is cold, start it and wait until the engine reaches operating temperature. Be careful, the old oil will be hot.

How much oil to pour into a Nissan Almera engine.

Step-by-step instruction

1. We warm up the engine and let it run for 10 minutes, then turn it off;
2. You need to place an empty container under the drain hole - we will pour the old lubricant into it;

Guide to filling a different brand of oil

If you decide to pour another lubricant for the Priora, then you need to flush the system. For this, special washing solutions are used, but you may not have them on hand. Then use the oil that you will pour:

1. After draining the old oils You should fill the new one up to the lower pointer on the dipstick. Check that the level is at MIN.
2. Start the engine and let it idle for a few minutes.
3. Drain the liquid completely and screw the filter securely.
4. Now you can flood new oil, the level should reach the upper mark.

Video instructions for changing the oil yourself.

Many Lada Priora owners carry out the necessary service work themselves, which allows them to significantly save on the operation of their car. We will tell you in more detail how to change the oil on a Priora.

Getting ready for replacement

Regular replacement of engine oil and the corresponding filter element ensures trouble-free operation of the power unit, the moving elements of which will be properly lubricated and cooled. That is why it is necessary, in full compliance with the recommendations of automakers, to change the oil on a car after a mileage of 10-15 thousand kilometers.

Such repair work does not pose any difficulty. Each car owner will be able to perform such work independently, which, in turn, will allow him to save about 2-3 thousand rubles, which he would have to pay at a service center for such an oil change in Priora.

What kind of oil to pour into the engine

There are no difficulties with choosing the oil and filter elements used. This engine is not so critical to the quality of consumables, so the car owner can purchase an inexpensive semi-synthetic Russian engine, which is recommended by this automaker.

If we talk about what kind of oil to pour into Priora, then most car owners purchase Lukoil lubricant, which in terms of its viscosity should correspond to the climatic region where the car is operated.

You will also need to purchase an oil filter for this job. It is best to buy it original in the appropriate stores, since its cost today is not too high.

Engine oil volume Priora

Priora is equipped with five engine modifications, the power of which ranges from 90 to 130 horsepower. Buyers are offered a choice of engines with a volume of 1.6-1.8 liters. These power units have a similar design and the same oil sump volume. To change the oil you will need 3.5 liters. It is best to buy a canister (4 liters), which will subsequently eliminate problems with adding lubricant during vehicle operation.

Oil, like most other cars, is poured through the upper neck on the cylinder head cover. When unscrewing such a filler plug, pay attention to the presence of carbon deposits and light emulsion. If there is abundant white foam and emulsion, this may indicate a violation of the tightness of the cylinder head, as a result of which antifreeze enters the oil, worsening its characteristics.

Changing the oil

This procedure is not particularly difficult; you do not need to use any professional tools or equipment, and it can take one hour to complete. Just remember the need to use high-quality consumable parts and lubricating fluids, which will eliminate any difficulties in the future with the operation of the car.

Tools used

To perform this work you will need a filter, engine oil, a clean rag, a container with a volume of at least 4 liters, a wrench for removing the oil filter, a 17 wrench.

If you do not have a special wrench for removing the oil filter, you can try to unscrew it by hand, wrapping it in sandpaper. Remember that this type of work is best done on a cold engine.

If you are unable to unscrew the filter manually, you can pierce its housing with a screwdriver and use it as a lever, thus removing the filter element. If you use a screwdriver to remove the filter, then you need to pierce its housing at the very bottom. This will prevent damage to the fitting.

Step-by-step instruction

1. Changing the engine oil must be done on a hot engine. To do this, you should either drive the car first, or start the engine and let the engine run for about 10 minutes. Warm oil will flow out easily through the lower hole, and you can almost completely drain it from the crankcase of the power unit.
2. To perform such service work, the vehicle must be driven onto a lift or inspection pit. Open the hood and unscrew the oil filler plug. You can easily unscrew this plug by hand.
3. Next, we go down under the car and remove the existing engine protection. We place a plastic container with a volume of at least 4 liters under the engine crankcase. We find the drain plug located on the engine crankcase, and then carefully loosen the tightening with a 17 key.
4. When unscrewing the plug, act as carefully as possible, as you can get burned by hot oil. We unscrew it completely and wait for the oil to completely drain out. This usually takes about half an hour.
5. If the car has a good mileage and the oil has not been changed for a long time, you can do this. Why is a special washing composition used? It is poured into the engine after twisting the drain plug. We start the engine and let it run for about 15 minutes. After this, drain the washing liquid and change the filter.
6. Replacing the oil filter is not particularly difficult. It is threaded and you just need to unscrew it, carefully draining the old oil. Fill the new filter element halfway with fresh auto lubricant and carefully screw it onto the mounting thread.
7. Please note the presence of a rubberized gasket, which is responsible for sealing such a connection. The filter must be tightened by hand three quarters of a turn from the point of contact between the cylinder block flange and the ring.
8. Next, pour approximately 3 liters of auto lubricant into the engine and check the level using a dipstick. The level should be in the middle between the minimum and maximum risk.
9. Then close the oil filler neck, start the engine, and let it idle for several minutes.
10. After this, we turn off the engine and wait for it to cool, check the oil level with a dipstick and, if necessary, add about 500 milliliters more. This completes all service work.

All owners of domestic cars are accustomed to servicing them independently, fortunately the simple design allows this. One of these cars is the 2007 Lada Priora, which is an updated version of the 1994 VAZ-2110. In terms of design, the machine has similar advantages and disadvantages, but is definitely better in terms of reliability. Any owner, even an inexperienced one, can cope with replacing consumables in a Lada Priora. So, one of the most basic procedures is changing the engine oil. No matter how simple this task is, questions may still arise, even among experienced motorists. In this article we will look at what points Lada Priora owners should pay attention to before replacing, as well as during this process.

The automaker recommends changing the engine oil in Lada Priora after 15 thousand kilometers, taking into account difficult climatic and road factors. In some cases, the interval has to be reduced to 8 thousand km. Thanks to this, the service life of the engine will be extended for the entire period of use of the car.

What will you need for replacement?

• Keys, including key number 17
• Container for draining used oil with a volume of 5 l
• Rags, rubber gloves
• New oil filter
• New 3.9 liter engine oil
• Special wrench for removing the oil filter (or screwdriver)

Which oil to choose for Lada Priora

Before you start replacing the fluid, you need to choose it correctly. In this case, we pay attention to various parameters, in particular SAE temperature viscosity, as well as API quality level. For example, if the fluid has parameters of 10w-40, then the oil is adapted to temperatures below minus 30 degrees. It is believed that the lower the number next to the letter W, the higher the adaptability to low temperatures. Typically, viscosity is selected depending on the climatic conditions in which the car is most often operated.

How much to fill

The optimal amount of oil to be poured into the Lada Priora engine is 4 liters.

What kind of oil filter is needed?

An oil filter from a VAZ-2108 is suitable for Lada Priora.

Sequence of oil change work

1. Having made sure that we have all the necessary tools, we get to work. First of all, warm up the engine to operating temperature. To do this, it is enough to travel around the city for 5-10 minutes
2. After the engine has warmed up, place the car on an overpass or lift.
3. Unscrew the drain plug at the bottom of the machine. If there is a motor protection installed there, it must first be removed to gain access to the plug. Please note that to remove the plug you will need the 17th key
4. After unscrewing the plug, the used oil will begin to drain from the hole into a pan prepared in advance
5. It takes 15 minutes for the liquid to drain completely. During this time, you can have time to do one more procedure - replace the oil filter. It is located on the right side of the exhaust manifold, that is, at the rear of the engine
6. So, to unscrew the filter you will need a special key. As a last resort, you can use a screwdriver to pierce the filter housing and use the screwdriver as a lever to unscrew the filter counterclockwise. It is possible that oil will leak from the filter, so you need to be careful. It is advisable to wear gloves
7. So, the old filter has been removed. We prepare the seat for the new filter - wash it, clean it and degrease it. Pour some oil into the filter and install it
8. After making sure that the old oil is completely drained, tightly screw the drain plug back into place and proceed to the next step.
9. Filling with new oil is done through the engine compartment. We provide access to it and find the filler plug. We insert a funnel into it and slowly pour in new oil, periodically checking the liquid level with a dipstick
10. For the Lada Priora engine, you need to pour in at least 3.5 liters of oil. After filling, we make a control measurement with a probe. It is necessary that the oil mark on the dipstick does not exceed the Max mark and does not fall below the Min mark. This is considered the ideal oil level
11. Screw the filler plug back into place. At this point, the process of changing the oil in the Lada Priora engine has been successfully completed.

Video