Change the fuel filter on Camry 40. Fuel filter Toyota Camry V40. When to replace the fuel filter
Many motorists have experienced first-hand that the quality of modern fuel leaves much to be desired. Often it contains various impurities such as sand, rust or metal scale. Without a filter, all this gets into the internal structure of the motor and can lead to breakdown. As a result, the driver will have to carry out expensive major repairs.
Also, the operation of the filter is closely related to the integrity of the candles. Untreated fuel burns only partially in the chamber, forming a deposit that settles on the cylinder walls and spark plugs. Because of this, the efficiency of the motor decreases significantly, and the service life of the spark plugs decreases. If you do not want to have the above problems, then replacing the fuel filter in the Toyota Camry 40 should be a mandatory procedure.
When to change the fuel filter on a Camry
One of the most popular questions among Toyota car owners is when to change the fuel filter on a Camry? First, you need to read the technical manual of your vehicle. It is there that clear information is given from the manufacturer regarding the frequency of replacement. This figure is catchy, so you should only partially rely on it. If you only use high quality fuel, then you will rarely have to change it.
But in the realities of life, everything is quite the opposite. Drivers recommend replacing them every 20-30 thousand kilometers. If the car is rarely used, then it is recommended to replace the fuel filter in the Toyota Camry at least once every two years. Failure to comply with these recommendations will result in clogging of the engine power supply system and fuel injection nozzles.
Main signs of a clogged filter
The fuel filter becomes unusable gradually, so it is quite difficult to judge its condition during the operation of the car. It may become clogged much faster than you drive 20 thousand kilometers. Here you need to pay attention to the signs of the car's behavior.
The most common signs of blockage are:
- Unstable engine operation, in particular, “sneezing” and instability at low speeds.
- Noticeable drop in power.
- Increased fuel consumption compared to normal levels.
If your car has one of the above problems, be sure to check the condition of the fuel filter.
Where is the Toyota Camry fuel filter located?
Many motorists are accustomed to the fact that the fuel filter is located in the engine compartment. On older cars this arrangement was natural. In modern foreign cars (including this Japanese one), this element is located directly in the fuel tank. You can access it under the rear seats in the cabin.
- It is recommended to carry out work outdoors. Large amounts of fumes can accumulate in an enclosed space.
- When replacing the filter, be sure to disconnect the terminals from the battery to prevent an accidental spark.
- Always have a fire extinguisher ready.
It is also necessary to relieve pressure from the system before work. To do this, simply open the outer gas cap. After this, you can proceed directly to replacing the fuel filter. To do this, prepare a set of keys, a Phillips screwdriver, and a brush or dust brush. Don't forget to buy a new filter. It is recommended to order an original product from the machine manufacturer. It guarantees proper operation for the entire specified period.
Main stages of the procedure
Replacing the fuel filter in a Toyota Camry is not particularly difficult. All actions will take you up to 30 minutes. To replace the fuel filter, follow these steps:
Thus, you can easily replace the fuel filter and save money on car service. It is also recommended to change the fuel pump mesh when replacing. This will help eliminate problems with the filter and pump in the future.
The fuel system provides fuel. To ensure that the gasoline supply occurs without interruptions, it is enough to ensure that consumables are replaced on time. One of the consumables - the fuel filter - can be updated even by an inexperienced motorist who knows how to hold a wrench and a screwdriver in his hands.
In older cars, the gasoline supply elements were located in the engine compartment. The design of modern cars is different, and manufacturers often install part of the equipment in the fuel tank. Therefore, there are owners who do not know where the fuel filter is located.
Access to the gas filter is provided by a hole located under the rear sofa. Therefore, the procedure should begin with dismantling the second row seats (there is no need to touch the backrests).
Replacement algorithm:
- Using a screwdriver, open the gas tank cavity cover. Care must be taken as there is wiring connected to it.
- Next, remove the terminal by pressing the tab.
After removing the cover and disconnecting the terminal
- Clean the space under the cover from dust with a brush or soft sponge.
- Tighten the 2 brackets with a screwdriver and move the stopper to the side to disconnect the hose.
- The next step is the protective cover itself. When you get to the pump cover, do not try to unscrew it with a screwdriver. It’s better to take a 8mm wrench and unscrew the bolts without any problems.
- Now you can remove the entire structure from the tank.
- Then the filter itself is disconnected.
- Then disassemble the cylindrical body.
- Disconnect terminals.
Disconnect the filter
- Disconnect the float from the body.
- Remove the retaining ring, spring and fasteners.
- Use a screwdriver to unscrew several latches at the top.
We continue to disassemble the pump
Completing pump disassembly
- Pull out the valve and remove the diaper from the fuel pump.
- The rubber seal from the valve is removed and replaced with the new pump.
- Treat the filter mesh with a special liquid and clean it so that no foreign bodies remain on it. If necessary, the mesh can also be replaced.
- Reassemble all components in reverse order.
- Install the new fuel filter in place.
- Start the engine and check the operation of the gasoline supply system.
Replacing the filter yourself will help you save money. But, if the car owner is not confident in his abilities, then it is better to entrust this procedure to specialists to avoid problems.
Required parts and tools
To replace, you need to prepare a new gas filter and several tools:
- pliers;
- screwdriver;
- wrench for 8;
- rags;
- special solution for cleaning the mesh;
- brush.
The original gasoline filter for a 2.4-liter engine differs from the gasoline filter intended for a car with a 3.5-liter unit. Therefore, you should carefully select the spare part according to the catalog number. The article number of the original 2.4 l filter is 7702433060. The price range is from 6,000 to 9,000 rubles.
The cost of auto parts for the more powerful version of the fortieth is cheaper and starts from 2 thousand. When purchasing, you should use the 3.5 l fuel filter number 2330021010.
The original coarse filter (mesh) is sold only complete with a pump. But you don’t have to change it, but rinse it well.
Coarse filter
If you want to change the mesh, then, with some effort, this filter can be found separately on the ebay resource. Part number from DEKO 232170H070. Also in the catalog its second name may be indicated - PT-25.
Analogs and fakes of the original
When purchasing an original fuel filter, there is a chance of receiving a counterfeit spare part. It can be determined by:
- poor processing of plastic at edges and joints;
- the presence of yellowness in the shade of plastic;
- lack of marking;
- difference in weight - the original has 232 g;
- The arrangement of the folds of the filter element should be fan-shaped or accordion-shaped.
But do not confuse fakes with analogues. After all, such substitutes for the original differ only in that they were not produced by divisions and partners. Otherwise, they meet all parameters and are produced by licensed enterprises. The most popular analogues suitable for installation on l are:
- JS ASAKASHI filter with number FS6305, which motorists consider the direct “successor” of the original;
- auto parts from Japan with code MFF-T110 from Masuma, which has the ideal combination of low price and excellent quality;
- German filter number ST 500 from SCT, which has gained popularity due to its reliability.
For machines with the most suitable analogues are:
- Japanese filter with article number MFF-T103 from Masuma, which is completely identical to the original;
- gasoline filter from Italy from Japan Parts, having catalog number FC-234S. However, there are doubts about this company that it is a manufacturer of spare parts, and not packaging containers.
A high-quality analogue will last no less than a Toyota gas filter, provided proper maintenance and adequate fuel quality.
When to replace the fuel filter
According to the technical manual from the manufacturers, the procedure for updating the fuel filter should be performed every 80 thousand km. At the same time, it is necessary to change the filter mesh or at least wash it with a special product.
Signs of a clogged gas filter:
- characteristic uneven sound of the fuel pump;
- increased fuel consumption;
- reduction in engine power;
- uneven operation of the motor;
- the engine stalls;
- the engine does not start.
But high quality domestic fuel is rare. Therefore, you will not have to replace the fuel filter more often than prescribed by the work regulations. The optimal service life of a gas filter is 20-30 thousand km with daily use.
If the car sits idle more than it drives, then the fuel filter needs to be changed at least once every 2 years.
Video
Regardless of the cost and brand of your car, it undoubtedly requires scheduled and sometimes unscheduled maintenance. In this case, we will consider such a problem as replacing the fuel filter. The scheduled replacement of the fuel filter is carried out once every 30,000 kilometers.
Reasons for replacement
The reasons for unscheduled replacement may vary. For example, you increasingly began to notice that the car loses traction at speed, stopped starting with half a turn of the key, smells of fuel in the cabin, or worst of all, stopped starting. It is necessary to change the fuel filter if your car spontaneously increases or decreases engine speed, even worse if it seems to be gassing. This is the first indication to replace the fuel filter on a Camry V50.
Replacement process
We proceed to directly replacing the filter on the Toyota Kmri. The gasoline filter is located at the rear of the car, on top of the fuel tank. The rear seat will need to be removed. In the middle part of the floor there is a protective block in which the gasoline filter is located. It is worth paying attention to cleaning the external unit from dirt before opening. Can be cleaned with a dry brush.
The next step, in order to relieve the pressure in the tank, is to open the filling cap, disconnect the electronic fuel supply sensor and remove the fuel pump hose. Using a tubular wrench for eight, unscrew the seven bolts, and then open the upper part of the protective unit. In front of you is the fuel pump itself. Before removing it from the tank, you will need to re-clean off the dirt with a brush so that debris does not get into the fuel. He should go out at ease.
Two steps are required to replace the filter. The first is to disconnect all electrical contacts, the second is to remove the fuel pump. We replace the old filter with a new one.
We must not forget about the O-rings, which are removed during disassembly of the unit. They are replaced with new ones and should be in the new set of your filter.
When replacing, it is recommended to wash the entire unit in gasoline, and then thoroughly blow it with a compression gun. Be sure to pay attention to the fact that when assembling the steel, each one is in its place without twists, and check them for cracks.
Failure to follow the rules for replacing the fuel filter may damage the gasoline pump. After performing these manipulations, you should reassemble the unit in the reverse order. When replacing the filter, the level of gasoline in the tank should exceed half; it would be best if it was full.
We start the car, we get a working fuel system. In a comprehensive pump filter replacement, the injectors are usually cleaned, while the pump unit is removed, the entire fuel system is washed and purged. After all operations to repair the fuel supply, you will need the help of a specialized electrician who will check the flow rate, quality and quantity of fuel, and of course reset the computer system errors. You should not be afraid of computer errors; this is the car’s defensive reaction to changes in engine operation.
Let's sum it up
The official Toyota Camry dealer does not recommend purchasing non-original repair kits. But over time, the owners, in order to reduce the cost of repairs on the Toyota Camry, purchased similar spare parts from the Camry V30. Many companies not related to the Japanese brand have established themselves as manufacturers of analogue original parts with a good reputation. The first spare parts hit the market for the Camry V30. In 2006, two manufacturers received the call, such as STP ST number 500, number 300, number 400. And the Camry drive company.
You can also watch a video on replacing the fuel filter on a Toyota Camry V40.
The Toyota Camry V40 on the domestic market was officially supplied with gasoline engines with volumes of 2.4 and 3.5 liters. In terms of configuration and characteristics, it is most similar to the Camry, which is supplied to the US market.
The fuel system on the Camry 40 is designed the same as on most modern cars. Fine and coarse fuel filters are placed in a single module together with the pump and installed in the tank. The filter for the Toyota Camry v40 differs depending on the engine being installed. Moreover, this applies to both the fine filter and the mesh filter.
Fuel filter Toyota Camry v40 2.4
Original fuel filter 7702433060
On the Camry 40 2.4, a fuel filter with the article number is installed from the manufacturer 7702433060 . The average price of a part is 6,000 rubles. The manufacturer is not indicated, neither on the packaging nor on the part itself. Many drivers have noticed that the original filter is almost identical to what JS ASAKASHI makes, its number is FS6305. Therefore, many Camry 40 car owners agree that the above-mentioned filter is a direct analogue of the original. Among drivers, fuel filter FS6305 is much more popular than the original, primarily because its price is on average 2 times lower - 1300 rubles.
The filter mesh, installed from the factory, is not sold separately and is only assembled with the fuel pump. The most suitable and popular original part is the mesh from DEKO under the article 232170H070. Price – 600 rub. It also has another name - PT-25.
Fuel filter dimensions 7702433060 for Camry 40 2.4
Due to the excessive cost of the original fuel filter, substitutes are also in great demand among drivers. The most popular of them:
- MFF-T110. Manufacturer: Masuma, Japan. Price - 1000 rub. This spare part is also popular among owners of the Camry v40 due to its low price and similar quality to the original;
- ST 500. Manufacturer – SCT, Germany. Price – 1100 rub. This filter has the same quality as the original. Many drivers recommend installing it because of its reliability.
Fuel filter Masuma MFF-T110
Fuel filter SCT ST 500
Fuel filter Toyota Camry v40 3.5
On a Toyota Camry v40 with a 3.5 liter engine, a fuel filter with the article number is installed from the factory 2330021010 . Price – 1600 rub. As in the first case (with a 2.4 engine), there is no exact information about the manufacturer of this part.
Original fuel filter 2330021010
JS ASAKASHI also has an identical filter FS6300, which, according to most car owners, is a direct analogue of the original Toyota fuel filter 2330021010 . Filter price FS6300– 540 rub.
It is worth noting that there are counterfeits of the original Toyota fuel filter on sale. 2330021010 . The main distinguishing features of a counterfeit part:
- poor processing of plastic edges of the part;
- the shade of the fake is more yellowish;
- there are no markings on the part itself;
- differences in weight. Weight of the original (without packaging) – 232 g;
- the usual arrangement of folds of the filter element. In the original, it is made in the form of an accordion, which increases the filtration area.
The mesh filter (coarse cleaning), which is installed by the manufacturer on the Camry 40 with a 3.5 engine, has article number 232170C010. Price – 450 rub. From detail 232170H070(which is installed on the Camry 40 2.4) is distinguished by a more elongated shape and the absence of a cutout.
Fuel filter dimensions 2330021010 for Camry 40 3.5
The most popular analogues of the original fuel filter 2330021010 are:
MFF-T103. Manufacturer: MASUMA, Japan. Price - 520 rub. According to reviews from drivers who used this filter, there is no difference with the original. The dimensions are also almost completely identical to the original part;
While operating a Toyota Camry, car owners may notice that the engine has begun to run unevenly, fuel consumption has increased, and the car's power has noticeably decreased. This indicates a faulty fuel filter. The manufacturer recommends replacing the fuel filter Toyota Camry V50, V40, V30 at least once every 80-90 thousand kilometers. But in practice this has to be done more often, since the quality of fuel in our country leaves much to be desired.
The replacement procedure for Toyota Camry V30, V40, V50 is identical. Unlike older models, here the unit is located not under the hood, but in the bank itself. It can be accessed through a special hatch located in the car interior under the rear seat.
No one is immune from the use of low-quality fuel; it occurs everywhere. To eliminate the harmful effects on the engine of rust, metal chips and other impurities that may be found in the fuel, a fuel filter is installed. Its task is to retain small debris so that it does not get into the motor, as this will lead to breakdown and, as a result, to expensive repairs.
If a filter replacement is necessary before the deadline set by the manufacturer, drivers most often notice this. The car loses power, has difficulty starting, the engine is unstable, especially at low speeds, and may stall. This indicates that the filter has stopped performing its functions normally and needs to be replaced.
How often should I change
The Toyota Camry manufacturer sets the frequency of replacing the fuel filter for models V30, 40, 50 - at least once every 80 thousand km. This indicator is not accurate; it largely depends on the quality of the fuel that the car owner uses. You need to focus on it if your car has traveled the specified number of kilometers and the fuel filter is working properly. If it is not replaced, as recommended by the manufacturer, then the breakdown will not take long to happen and may happen at the wrong time.
Practice shows that Camry v50 fuel filter replacement, V40, V30 is needed more often - after 30 thousand km. Typically, at this mileage, signs of clogging will begin to appear. If this happens, you should contact a service station or replace the unit yourself, since the fuel filter has stopped working properly and may allow small debris to pass through, which threatens to damage the injection system and the engine as a whole.
Before changing the filter, you need to prepare the car and tools. After completing the procedure, be sure to check whether all parts are well secured and whether there is any undercutting from under the hose.Precautionary measures
If you decide to carry out the procedure yourself, you need to study, for example, video of replacing the fuel filter Toyota Camry v40. Be sure to follow safety rules - when replacing, there may be a gasoline leak, an accumulation of fumes, which poses a risk of fire.
Before replacing you must:
- Drive the car out of the garage into the open air to prevent the accumulation of gasoline vapors.
- Remove sources of open flame, including turning off the power to the car by disconnecting the battery.
- Relieve pressure in the fuel system (just open the tank cap).
- Keep fire extinguishing agents on hand.
Next we proceed to replacing the fuel filter Toyota Camry 30. It is worth paying attention that it is recommended to buy high-quality spare parts recommended by the manufacturer, since only they guarantee reliable, long-term operation.
Replacement
The replacement process cannot be called complicated. Those who have practical repair experience will not have any difficulties. Before starting the procedure, you need to prepare the tools that may be needed:
- a set of keys;
- Phillips screwdriver;
- brush.
- It is necessary to remove the rear seat sofa.
- Disconnect the terminal by pressing the tab and pulling it towards you.
- Take a brush and clean off any dust that may have accumulated under the lid.
- Disconnect the hose; to do this, simply pry up the brackets with a screwdriver and move the stopper to the side.
- After this, the entire structure can be removed from the tank.
- Disconnect the wires.
- At the top of the structure there are several more latches that can be removed using a screwdriver.
- Remove the filter itself from the housing.
- Assemble all the parts for the new spare part and install it in place.
- Start the car.
Examination
After replacing the fuel filter Toyota Camry 40. 30 or 50, it is necessary to let the engine run a little. In this case, the engine may operate unstably, since air may have entered the system when replacing the filter. After a few minutes, the car is turned off and checked for gasoline leaks.
It will take no more than half an hour. This is a simple procedure that needs to be done regularly. If you do it yourself, you can save money and not contact a service station. Experts recommend replacing the fuel pump grid at the same time. This will extend the life of the new filter.
