We choose what oil to fill into the engine of a Chevrolet Cruze: volumes. The best oil for Chevrolet Cruze Recommended oils for Chevrolet Cruze 1.8

The selection of lubricant is made taking into account the engine parameters and its technical characteristics. The operating instructions recommend using only products that meet the vehicle manufacturer's requirements. The use of fluids and oils that do not meet these requirements may cause damage not covered by the warranty. In this article, we invite you to familiarize yourself with the recommended engine oils for the Chevrolet Cruze.

Model 2004 release.

For this vehicle range, use API classification oil - SG, SH, SJ, SL.

Select viscosity (SAE) according to the temperature range diagram corresponding to the operating conditions of the vehicle until the next oil change.

Caution: As engine oil viscosity increases, fuel consumption increases, so lower viscosity oils provide better fuel economy. In hot weather, more viscous oils provide better lubrication.

Viscosity temperature range diagram.

Attention: it is recommended to be careful when using low-viscosity motor oils (such as 0W - 20) in cars with high mileage or in warm seasons (for example, summer). When using such oils, you should be sure that the engine and its seals are in good condition.

The volume of motor fluid for a Chevrolet Cruze when replacing it is presented below.

Refill capacity:

  • Dry engine - 4.1 l;
  • With filter replacement - 3.8 l;
  • Without filter replacement - 3.6 l.

Chevrolet Cruze 2009-2015


Model 2011 release.

When to change engine oil

The electronic system of the Chevrolet Cruze will promptly warn you about the need to change the oil and filter. The calculation is based on engine speed and operating temperature; mileage is not taken into account. Based on driving conditions, the need to change the oil may occur at different mileage levels.

To ensure stable operation of the system, it must be reset after each oil change. When the system calculates that the oil has reached the end of its service life, it will notify the driver about the need to change the oil. The CodE 82 symbol will appear in the driver information center. In this case, the oil must be changed as soon as possible; the permissible mileage before changing the oil should not exceed 1000 km.

Under certain conditions (favorable driving conditions), the system may not indicate the need for an oil change for more than a year. The engine oil and filter must be changed at least once a year, and the system must be reset at the same time.

Engine oil life display

The remaining engine oil life is displayed in the Driver Information Center by the I indicator, followed by the percentage of engine oil life remaining. To do this, turn on the ignition and do not start the engine.

Choosing engine oil

Motor oil is characterized by quality and viscosity. When choosing motor oil, know that quality is much more important than its viscosity. It affects engine cleanliness, wear protection, and the rate of oil aging; and viscosity indicates the stability of the oil’s properties during temperature fluctuations.

1. Engine oil quality

Buy dexos certified motor oils. This mark guarantees that the quality of the oil meets the requirements of the dexos specification.

The Chevrolet Cruze was initially filled with approved dexos engine oil at the factory. Use only dexos approved oils or similar oils with the appropriate viscosity level. Information about what tolerances a specific motor oil is certified to can be found on the label.

If you are not sure about the quality of the oil you are using, contact your authorized dealer.

The choice of engine oil is influenced by the performance characteristics of the oil, as well as its viscosity.

2. Engine oil viscosity index
Engine oil viscosity depending on temperature.

SAE 5W-30 is the optimal oil viscosity value for your car. Do not use oils with SAE viscosity 10W-30, 10W-40 or 20W-50.

Work at low temperatures. In countries with cold climates, when temperatures drop to -25 °C, an oil type with a viscosity of SAE 0W-30 (for winter) should be used. Oil of this viscosity makes it easier to start the engine at very low temperatures. When choosing an oil of the required viscosity, pay attention to the presence of the dexos marking.

  • Up to -25 °C and below: 0W-30, 0W-40;
  • Up to -25 °C: 5W-30, 5W-40;
  • Up to -20 °C: 10W-30, 10W-40 (only for LXT);
  • Up to -15 °C: 15W-30, 15W-40 (LXT only).

SAE Viscosity provides information about the viscosity of an oil. Universal oil is designated by two codes. All-season oil is designated by two numbers separated by the letter W.

Viscosity is designated by numbers: the first followed by the letter W indicates low-temperature viscosity, the second indicates high-temperature viscosity.

Warning!

All of these substances are dangerous and can be poisonous. Handle them with care. Read the information on the packages.

Topping up engine oil

If motor oils from different manufacturers and brands meet the accepted requirements for quality and viscosity, then they can be mixed.

If engine oil of the required quality is not available, no more than one liter of ACEA A3/B4 or A3/B3 class oil can be used (no more than once per oil change). The oil must have the appropriate viscosity. The use of only ACEA A1/B1 or A5/B5 grade oil is strictly prohibited as serious engine damage may occur under certain conditions.

Using other oils when dexos oils are not available

If dexos oils are not available, other oils can be used to top up to the required level in the quantities indicated above. It should be remembered that the use of oils that do not meet the dexos specification, under certain conditions, can lead to a deterioration in the traction and power characteristics of the engine or its failure.

Motor oil additives

The use of other motor oil additives may cause engine problems and will void the warranty.

Changing the oil is one of the most important procedures in engine maintenance. It is important to know what kind of oil to fill in a Chevrolet Cruze so that you use the right brand. At the factory, parts are developed taking into account the characteristics of the oil that will be poured into this model. If you want to choose a different type or brand, buy only liquids that are similar in properties.

Types of motor oils

There are three types of oils:

  1. Mineral. The advantage of this type is its low cost. The properties are very viscous, well suited for cars with a mileage of more than 150 thousand km. The disadvantage is that it needs to be changed frequently, every 9-10 thousand km. At high temperatures it loses its properties and cannot withstand engine overheating.
  2. Semi-synthetic. Mineral base with synthetic additives. Consumers choose this type to save on synthetics.
  3. Synthetic. The best engine oil for Chevrolet Cruze. Compared to previous types, it has many advantages: long service life, lubricates well. Does not lose its properties at low temperatures and is resistant to overheating. The only drawback is the high cost.

Advice! When you switch from one manufacturer to another, the main thing is to find a liquid with the same characteristics. Mixing different types is highly discouraged.

What to fill in a Chevrolet Cruze

The best oil for Chevrolet Cruze is with a viscosity of 5W-30. This is an all-season liquid, suitable for summer and winter. It is recommended to use it from -25 to +20 degrees. The 5W-40 marking means that the liquid can withstand temperatures from -25 to +35 degrees. You can choose the viscosity that suits your region.

Ideal for this car:


If you decide to change the viscosity or brand, it is better to use a flush to remove any remaining old fluid from the engine.

Oil volume

Lack of fluid in the engine is a cause for concern. Different engines consume oil differently. Some engines need topping up 1-2 times between replacements, and some require more. If you notice that the engine begins to ask for more fluid than before, this is a reason to look for the cause.

On 1.4 and 1.6 liter engines, the volume of technical fluid is 3.5 liters. For a 1.8 liter engine - volume is 4.5 liters. It is recommended to purchase an additional 1 liter for refilling.

How to check the level

If you don’t know how to check the oil level in a Chevrolet Cruze, read our instructions:

  1. Park the car on a level surface.
  2. Turn off the engine and wait 10 minutes. During this time, all the oil will drain from the channels and parts. If you do not pay attention to this point, most likely the level will be low and you will have to add fluid. As a result, this will lead to a critical level and compression of the seals.
  3. Under the hood, locate the dipstick that sticks out from the cylinder block. Take it out and wipe it with a clean cloth. Put it back in.
  4. Take out the dipstick and find two notches on it - minimum and maximum. The normal level is in between.
  5. If the level is below the minimum, you need to add more fluid.

How often does it need replacement?

  • driving conditions;
  • driving style;
  • fuel quality;
  • ambient temperature;
  • quality of technical fluid;
  • quality of roads (their dustiness).

The level and quality of engine oil should be checked periodically. If it darkens and becomes cloudy, then it’s time to change it.

You can come to the official dealer for technical oil with your own consumables, if this is not prohibited by the rules in your city. You can decide for yourself which oil is best to fill in the Chevrolet Cruze, and not use what dealers usually fill.

Each car enthusiast must decide for himself which oil is best for the Chevrolet Cruze, since it depends on the degree of wear of parts, driving style, and operating conditions.

The durability and reliability of the Chevrolet Cruze engine is largely determined by the timeliness of replacement and the quality of the oil being poured. Violation of one of the listed criteria leads to deterioration in lubrication of rubbing surfaces, which may result in scoring. This reduces the life of the power plant and increases the need for expensive overhauls. Therefore, you should use the best recommended oil and observe the replacement intervals.

Choosing oil for a Chevrolet Cruze engine

ATTENTION! A completely simple way to reduce fuel consumption has been found! Don't believe me? An auto mechanic with 15 years of experience also didn’t believe it until he tried it. And now he saves 35,000 rubles a year on gasoline!

Original General Motors oil “Dexos 2” 5W-30

The original oil poured into the Chevrolet Cruze engine from the factory is General Motors “Dexos 2” 5W-30. Reviews from car owners about branded lubricant are very opposite. Some believe that it is not worth buying products from third-party manufacturers, but many argue that the GM “Dexos 2” brand forms a lot of deposits in the engine, even if replaced in a timely manner. The cost of branded oil is about 1500 - 2900 rubles.

General Motors allows the use of oil with viscosity 0w30, 0w40, 5w30, 5w40, 10w30, 10w40. Recommended third-party manufacturers and their product prices are listed in the table below. Any non-branded oil that a car owner wants to fill must have dexos2 approvals.

Oil for Chevrolet Cruze from a third-party manufacturer

Engine oil filling volume

How much oil is required depends on the engine size and replacement method. So, depending on the power plant, you will need:

  • for a 1.4 liter engine and 140 hp. filling volume is 4 l;
  • for a 1.6-liter and 109-liter power plant, 4.5 liters are required;
  • for a 1.6-liter engine with 124 hp. 4.5 l required;
  • for the most powerful power unit of 1.8 and 141 hp. 4.5 liters required.

When changing brands, it is advisable to flush the engine. Therefore, the required volume of oil can increase to 7-8 liters.

Replacement frequency

The official manufacturer recommends changing General Motors “Dexos 2” 5W-30 oil every 15,000 kilometers or 2 years of operation, whichever comes first. Experienced car owners recommend reducing the replacement interval to 10,000 kilometers. During urban vehicle use, even such a reduction in the lubricant change period may not be enough.

The photo below shows a 2011 f16d engine with the valve cover removed. Its mileage is just over 65,000 kilometers. The oil was used exclusively original and changed every 10 thousand km. Despite this, there is a lot of deposits under the valve cover.

Engine with valve cover removed

For the above reason, if the car is frequently used in city traffic jams, it is recommended to reduce the oil change interval to 5-7 thousand kilometers. A similar rule applies to the use of lubricants from third-party manufacturers. The car owner must determine how much it costs to drive until the next replacement, based on operating conditions and the condition of the fluid being drained.

In addition, changing the engine oil ahead of schedule will be required in the following cases:

  • foreign technical fluid has entered the lubricant, for example, antifreeze or slurry poured into the steering wheel;
  • the engine overheated;
  • the oil froze in winter;
  • a crack was found in the box through which lubricant enters the motor;
  • spark plugs often fail;
  • an increase in the level of lubrication was noticed;
  • Water got into the oil.

You can determine the condition of the lubricant by dropping it onto a napkin. You can determine the need for an oil change by comparing the spot to the image below.

Determining the condition of the oil by a stain on a napkin

Normal oil consumption in a Chevrolet Cruze engine

The manufacturer considers oil consumption to be up to 1 liter per 1000 kilometers as normal. Exceeding this indicator indicates the need to repair the power unit.

According to reviews from experienced car owners, engine oil consumption in normal technical condition rarely exceeds 150-200 grams per 1000 km. Usually, during operation, there is enough lubricant from filling to filling, so additional pouring is necessary only on worn-out motors.

Required Tools

In order to successfully change the oil yourself, you need the tools shown in the table below.

Also, for replacement you will need a container for draining waste and rags.

Consumables that will be needed for replacement

  • Oil filter, article number 96879797 or 93185674. Its cost is about 480 rubles. You can use a cheaper filter MANN-FILTER HU6122X, the price for which is 350 rubles. Bosch F026407006 has also proven itself well, costing about 250 rubles.
  • Rubber gasket for engine oil drain plug. Its article number is 90528145 or 94525114. The cost is in the range of 30-40 rubles.

DIY oil change process on a Chevrolet Cruze

Change the engine oil according to the instructions below.

  • Warm up the engine.
  • Raise the car on a lift or install it above the inspection hole.
  • Open the hood.

Appearance of the engine compartment

  • Go down into the viewing hole.
  • Place a container under the drain plug.
  • Using a ratchet with an extension, unscrew the drain plug.

Unscrewing the drain plug

  • Remove the plug and visually assess the condition of the drained oil. It should be taken into account that how much liquid will drain depends on its temperature.

Oil draining process

  • Change the sealing gasket on the drain plug

Replacing the gasket

  • Unscrew the cover with the oil filter housing.

Removing the oil filter

  • Install a new filter element into the housing.

Installing a new filter element

  • Place the new filter in place.

Oil filter installation

  • Tighten the oil filter cap using a wrench.

Filter installation process

  • Screw in the drain plug.

The process of tightening the drain plug

  • Pour fresh oil into the engine.

Filling oil

  • Using a dipstick, check the engine oil level.
  • Start the engine. If the warning light comes on about insufficient lubricant pressure, then there is nothing to worry about. After some time, the indicator should go out.
  • Check the oil level and add if necessary.

Chevrolet Cruze 1.6 is a middle-class car, very popular on the Russian market. The car is no longer officially for sale, and today it is in demand on the supported market. Most owners of such cars prefer to maintain them on their own, not wanting to pay for expensive repairs. At the very least, you can perform basic procedures yourself, for example, pour new oil into the engine. But before that you need to choose the right oil. This issue is given special attention in this article. The material indicates the recommended parameters and brands of oils separately for each model year of the Chevrolet Cruze with a 1.6-liter engine, starting from 2009.

Model range Chevrolet Cruze J300 2009

  • Recommended viscosity depending on ambient temperature (season):
  • For any season – 10W-40, 15W-40, 5W-40
  • For winter conditions – 0W-40, 0W-30, 5W-40
  • For summer conditions – 20W-40, 25W-40
  • Quality class according to API standard: for gasoline engines - SM
  • Recommended brands – Xado, Castrol, ZIK, Kixx, Lukoil, Valvoline, Mobile.

Model range 2010:

  • Recommended SAE viscosity parameters:
  • All-season: 10W-40, 5W-40, 15W-40
  • Winter: 0W40, 5W-40
  • Summer:20W-40, 20W-40
  • Recommended oil - synthetic, semi-synthetic
  • Recommended brands – Castrol, Xado, Mobile, Shell, Lukoil, GT-Oil, ZIK, Valvoline.

Model range 2011

  • Recommended viscosity parameters according to SAE class:
  • All-season: 5W-40, 10W-40, 10W-50, 15W-40
  • Winter: 0W-40, 5W-40, 5W-50
  • Summer: 20W-40, 25W-40, 25W-50
  • By API class: for gasoline engines - SM
  • Recommended oil: synthetic, semi-synthetic
  • Recommended brands: ZIK, Shell, Lukoil, Castrol, Valvoline, Xado, Mobile

Model range 2012

  • Recommended viscosity parameters depending on temperature:
  • All-season: 10W-50, 5W-40, 15W-40
  • Winter: 0W-40, 5W-50
  • Summer: 20W-40, 25W-50
  • Recommended brands: Shell, Mobile, Castrol, Lukoil, ZIK, Xado, GT-Oil, Valvoline

Model range 2013:

  • Recommended parameters for SAE class:
  • All-season: 10W-50, 15W-40, 15W-50
  • Winter: 0W-40, 0W-50
  • Summer: 20W-40, 25W-50
  • By API class: for gasoline engines - SN
  • Recommended oil: synthetic
  • Recommended – Mobile, Castrol, ZIK, Shell, Xado.

Model range 2014

  • Recommended parameters for SAE class:
  • All-season: 15W-50, 10W-50, 15W-40
  • Winter: 0W-40, 0W-50
  • Summer: 20W-40, 25W50
  • By API class: For gasoline engines - SN
  • Recommended oil: synthetic
  • Recommended brands – Xado, Shell, Castrol, Mobile

Conclusion

If financial capabilities allow, it is better to buy original oil. But we must admit that today this is not always advisable, given the many cheaper analogues. The main thing is that their parameters meet the recommended ones.

Oil change video


It is no secret that the original motor oil, which the car manufacturer recommends to be poured into the engine, is the most suitable for the car. Thus, in the Chevrolet Cruze it is recommended to use GM Dexos lubricant. For new cars and cars with low mileage, synthetic motor oil from any manufacturer is best suited, the main thing is that the properties of the lubricating fluid meet the necessary requirements in terms of their parameters. Gasoline engines of models with a production year before 2012 must be serviced with oils with a class (according to API) not lower than SM, and for newer cars - SN and higher. And if engines with a production year of 2011 and earlier can safely be filled with semi-synthetic oil, the design of modern engines does not allow this, and the plant recommends pouring exclusively synthetic oil. If engine parts have significant wear, oil consumption has increased, and engine power and throttle response have decreased, then when changing the oil, you can switch to a more viscous, semi-synthetic oil. This will allow you to operate the car for some more time without major engine repairs, while not forgetting to reduce the intervals between replacements to 6-7 thousand (semi-synthetic oil loses its properties much faster than synthetics, which can easily “nurse” up to 15 thousand km ).

When selecting analogues of the original oil, we are usually guided by the following selection criteria:

  1. Compliance of lubricant characteristics with the basic recommendations of the plant;
  2. Reliability of the brand, absence of counterfeit;
  3. Reviews from other owners, advice from motorists and qualified Chevrolet Cruze service specialists;
  4. Cost and availability of motor oil.

The huge assortment of the modern domestic market for lubricating consumables makes it difficult to choose, which, as a rule, is narrowed down to 2-3 types of suitable oils available for sale at the nearest spare parts store.

Our review presents the best motor fluids that can be filled into a Chevrolet Cruze with a gasoline engine. When selecting them for our rating, we were guided by the compatibility of oils with the requirements of the car plant, the popularity of the brand, existing experience in use, research and comparative analysis, which were published by popular and authoritative publications on automotive topics.

The best synthetic oils

Pure synthetics have excellent properties that are most suitable for modern engines. The active additives used in the base oil greatly increase engine protection against wear, take care of internal cleanliness and successfully prevent engine overheating. This category of our rating contains the best synthetic oils that can be poured into a Chevrolet Cruze engine.

5 Castrol Edge Professional 0W-40

Double wear protection system
A country: England (Produced in Belgium)
Average price: 2,920 rub.
Rating (2019): 4.6

The creation of this oil is based on the innovative TITANIUM FST technology, which allows titanium molecules to increase the surface tension of the lubricating fluid, making the oil film on friction pairs twice as reliable. It is not only tear-resistant, but also able to withstand mechanical damage.

In addition, as the load on the engine increases, the oil moves to a new molecular level, due to which the layer of oil film increases and part of it begins to absorb the impacts of parts during rapid rotation, effectively preventing damage at maximum (and exceeding established speed limits). Reviews note quieter operation, fuel economy, lack of carbon deposits and the need to top up engine oil.

4 Motul X-clean 8100 5w40

The most durable oil film. Extended service life
Country: France
Average price: RUB 3,042.
Rating (2019): 4.6

Fully complies with Euro-5 eco-standard. Low ash content is not only a concern for the environment, but also allows you to keep the particulate filters and catalytic converters of modern cars clean. The nature and intensity of temperature loads does not affect the strength of the oil film - in any operating mode, engine parts receive enough lubrication for reliable operation.

Reviews about the use of oil in the Chevrolet Cruze talk about fast oil pumping, good engine starting parameters at low temperatures, no carbon deposits and the need to top up the oil during operation (between changes), the period of which can be increased, because the properties of the lubricant do not change even after 15 thousand mileage. There is also evidence that thanks to this engine oil, the Chevrolet Cruze with 1.6 liters. engine saves fuel.

3 GM Dexos 2 5W – 30

Of course, the plant cannot insist on using this particular oil in Chevrolet Cruze cars, but it strongly recommends doing so. In any case, it is filled most often at Chevrolet service stations. GM Dexos 2 engine oil has a good and affordable price (for synthetics) and confidently copes with its tasks, providing lubrication to engine parts in any operating mode.

However, there are numerous reviews in which the owners do not speak very well of the properties of this oil, characterizing it more as an average quality lubricant. And the excellent environmental performance characteristics of GM Dexos 2 were achieved at the expense of cleaning and antioxidant properties.

2 LIQUI MOLY Synthoil High Tech 5W-40

High cleaning power
Country: Germany
Average price: RUB 3,452.
Rating (2019): 4.9

This best motor oil was obtained through the synthesis of polyalphaolefin hydrocarbons. Due to its artificial origin, Synthoil High Tech oil is stable and does not change its properties under the influence of sudden temperature changes, does not evaporate and is not capable of contaminating the surfaces of parts with soot and sludge deposits. If contaminants are already present in the engine, then the lubricant will carefully rid the engine of accumulated sediment in just one cycle - the cleaning abilities of this oil are the most powerful.

From the reviews we can conclude that this engine oil does not age, retains its characteristics throughout its service life, and the period between replacements is much longer than its analogues (there is experience of mileage from replacement to replacement of 20 thousand km). In addition, the oil contributes to effective fuel economy.

1 Total Quartz Energy 0W30

The best additive package
Country: France
Average price: RUB 2,081.
Rating (2019): 4.9

Reviews from owners who operate their Chevrolet Cruze engines with this oil note excellent cleaning characteristics, quieter and more stable engine operation, as well as the oil’s ability to neutralize the damage caused to the engine by poor quality fuel. The main thing is to replace it on time and choose the best quality oil filter when servicing the engine oil system. By the way, Elf Excellium oil is its complete analogue.

When changing the oil on a Chevrolet Cruze, you should remember that for an engine with a volume of 1.6 liters, it is quite enough to purchase a 4-liter canister (3.5 liters are poured into the engine during replacement and still remain for topping up until the next lubricant change). For a more powerful power plant (1.8 liters), this volume will no longer be enough.

The best semi-synthetic oils

Semi-synthetics can be used not only in older models, but also in modern engines with high mileage, where there is already noticeable wear. In addition, the most common 1.6-liter F16D3 engine can be found not only in the Chevrolet Cruze but also in such popular models as Opel, Daewoo Nexia and Chevrolet Lacetti. Running on high-quality semi-synthetics, the engine can travel 400,000 km without major repairs. and more.

3 Mannol Molibden Gasoline 10W-40

High-quality wear protection. Best price
A country: Germany (produced in Lithuania)
Average price: 763 rub.
Rating (2019): 4.2

This oil initially has a dark color, which is given by an additive with molybdenum disulfide. It is this that increases the surface tension of the engine oil, due to which all friction pairs at the time of starting the engine are protected by an oil film, which remains even after a long break in engine operation.

 
Articles By topic:
Selection of equipment, consumables and crew perks
06/25/2016, 19:29 Hello everyone and welcome to the site! Today we will talk about a new premium car, which may appear in our favorite game in the near future. We are talking about an American medium tank located on the eighth level -
Capitalize fuel cards in 1c
The increase in the flow of vehicles on the roads of Moscow and the region, as well as in large regional cities, has led to the need to develop more advanced and favorable conditions for cooperation between fuel organizations and their customers. Cost and quality of fuel, opera
Piranha LEDs – what are they?
In our previous articles, we have described many times the process of making a board for installing various LED modules in a car. Using the LUT method provides very wide opportunities for realizing the most daring ideas. However, lately everything
Piranha LEDs – what are they?
In our previous articles, we have described many times the process of making a board for installing various LED modules in a car. Using the LUT method provides very wide opportunities for realizing the most daring ideas. However, lately everything